Ubiquiti U-PoE++ PoE++ Adapter 60W (U-PoE++): Single-Port 60W Power for UniFi PTZ Cameras, Access Hubs and Mesh APs
The Ubiquiti U-PoE++ is a single-port PoE++ adapter (injector) that sends up to 60W of power and Gigabit data over one Ethernet cable to UniFi PoE++ devices. It converts 100–240V AC mains into a 48V DC, 1.25A output across all four cable pairs, so high-draw devices such as the UniFi G4 PTZ camera and the UniFi Access Hub (UA Hub) run without a PoE++ switch. In addition, the adapter has surge, peak pulse and overcurrent protection, a grounded IEC-320 C6 AC cable and shielded RJ45 sockets for both the data-in and PoE ports. As a result, it guards the powered device and the upstream network against power spikes.
In practice, a gate camera at a Karen home or a mesh access point at the far end of a Kitengela warehouse often sits where no PoE++ switch port is free. Therefore, the U-PoE++ lets you keep your existing switch, even a non-PoE model, and add 60W only where you need it. Similarly, it takes load off a PoE switch whose power budget is already shared among cameras and VoIP phones. Furthermore, because it runs from ordinary mains, you can plug it into a UPS so a PTZ camera keeps recording through KPLC outages. Meanwhile, the same office network that links your HP Desktops to the NVR carries the camera’s video through the adapter’s Gigabit port. However, the output is 48V DC, so connect it only to devices that accept 48V PoE input.
Key Features
In short, this PoE++ adapter stands out in five areas:
- Up to 60W PoE++ output at 48V DC, 1.25A
- 4-pair powering on pins 1, 2, 4, 5 (+) and 3, 6, 7, 8 (−)
- Gigabit LAN pass-through through shielded RJ45 data-in and PoE sockets
- Surge, peak pulse and overcurrent protection in differential and common mode
- Universal 100–240V AC input with 85%+ efficiency and a grounded IEC-320 C6 cable
Technical Specifications
Specifically, the table below details every core specification of the Ubiquiti U-PoE++:
| Specification | Details |
|---|---|
| Brand | Ubiquiti UniFi |
| Model | U-PoE++ |
| Product Type | PoE++ adapter (single-port injector) |
| Colour | White |
| Max. PoE Output | 60W |
| Output Voltage | 48V DC @ 1.25A |
| Powering Method | 4-pair |
| Pin Assignment | Pins 1, 2, 4, 5 (+) and 3, 6, 7, 8 (−) |
| Gigabit LAN Port | Yes |
| Data In / PoE Ports | RJ45 shielded sockets |
| Power Method | Universal AC input |
| Rated Voltage | 100–240V AC, 50/60Hz |
| AC Connector | IEC-320 C6 (earth-grounded cable) |
| Input Current | 1.3A @ 120V AC; 0.75A @ 230V AC |
| Inrush Current | <100A peak @ 120V AC; <200A peak @ 230V AC |
| Efficiency | 85%+ |
| Switching Frequency | 65kHz |
| Output Ripple | 1% max. |
| Line Regulation | ≤1% |
| Load Regulation | ≤3% |
| Surge Protection | Differential and common mode |
| Max. Surge Discharge | 1500A (8/20μs), power |
| Peak Pulse Current | 36A (10/1000μs), data |
| Clamping Protection | 11V data, 60V power |
| Response Time | <1ns |
| Shunt Capacitance | <5pF, data |
| LAN Activity Indicator | No |
| Reset Button | No |
| Remote Reset | No |
| Dimensions | 106 x 63 x 34mm |
| Weight | 210g |
| Operating Temperature | 0 to 40°C |
| Storage Temperature | -30 to 70°C |
| Operating Humidity | 10–95% non-condensing |
| Certifications | CE, FCC, IC, UL, UKCA, KC, CCC, RoHS |
Who This PoE++ Adapter Is Best Suited For
As a result of this combination of specs, three types of users benefit most:
- CCTV and access control installers who need to power a UniFi G4 PTZ camera or UA Hub from a switch without PoE++ ports
- UniFi network integrators who extend Wi-Fi with mesh access points at gates, car parks or outbuildings far from the main rack
- SMEs and offices whose PoE switch budget is already taken up by cameras and phones and who need to add one high-power device


Reviews
There are no reviews yet.