Ubiquiti Ethernet Surge Protector Gen 2 (ETH-SP-G2)

KSh 3,500

In StockReady to ship
  • Fast DeliveryWe deliver to all towns & cities in Kenya
  • Warranty InclusiveThis product is covered by warranty
Ubiquiti Ethernet Surge Protector Gen 2 (ETH-SP-G2)
Ubiquiti Ethernet Surge Protector Gen 2 (ETH-SP-G2)
KSh 3,500

Ubiquiti Ethernet Surge Protector Gen 2 (ETH-SP-G2) – Grounded Outdoor Surge and ESD Protection for PoE Network Links

The Ubiquiti Ethernet Surge Protector Gen 2 (ETH-SP-G2) is a compact, outdoor in-line surge protector that sits on an Ethernet cable between two network devices and diverts electrostatic discharge (ESD) and surges to ground. It has two passive, surge-protected RJ45 ports, so it works with PoE and non-PoE devices on 10/100/1000 Ethernet links, including IEEE 802.3af PoE. Compared with the first generation, it is rated for a discharge current of 10kA+, with a 700V maximum impulse spark-over voltage and 1.0pF maximum capacitance that keeps data loss on the line low. In addition, the IPX5-rated enclosure handles rain and mounts on a wall or pole, and it operates from -30 to 65°C. The unit measures 91 x 61 x 32.5mm and weighs 80g.

Lightning during the long and short rains is a leading cause of damaged routers, switches and radios on Kenyan rooftop links. Because a surge often travels down the Ethernet cable from the outdoor radio, it can destroy the indoor equipment as well. Therefore, Ubiquiti recommends one ETH-SP-G2 near the outdoor device and another where the cable enters the building, with both connected to ground. For example, a WISP in Kisii can protect each subscriber’s router and avoid repeated call-outs after storms. Similarly, a lodge in the Maasai Mara can shield its reception switch from surges on a long cable run to an outdoor camera. Note that the protector needs a proper ground connection to work, so connect its ground wire to an earth point during installation.

Key Features

In short, this surge protector stands out in five areas:

  • 10kA+ discharge current for surge and ESD protection
  • 2 passive, surge-protected RJ45 ports for PoE and non-PoE links
  • 10/100/1000 Ethernet with 802.3af PoE support
  • IPX5 outdoor enclosure, wall or pole mount
  • -30 to 65°C operating range in a compact 80g body

Technical Specifications

Specifically, the table below details every core specification of the Ubiquiti ETH-SP-G2:

SpecificationDetails
BrandUbiquiti
ModelETH-SP-G2 (Ethernet Surge Protector Gen 2)
Product TypeOutdoor in-line Ethernet surge and ESD protector
Interface Connections2 x RJ45 female (passive, surge-protected)
Data Line ProtectionRJ45 10/100/1000 Ethernet
IEEE 802.3af PoE SupportYes
DC Spark-Over Voltage90V @ 100V/s
Max. Impulse Spark-Over Voltage700V @ 1kV/µs
Discharge Current10kA+
Max. Insulation Resistance1G ohm @ 50V
Max. Capacitance1.0pF @ 1MHz
WeatherproofingIPX5
EnclosureWhite polycarbonate
MountingWall or pole
Dimensions91 x 61 x 32.5mm
Weight80g
Operating Temperature-30 to 65°C
Operating Humidity10–90% non-condensing
Shock and VibrationETSI 300-019-1-4

Who This Surge Protector Is Best Suited For

As a result of this combination of grounded surge protection and an outdoor enclosure, three types of users benefit most:

  • WISPs protecting subscriber routers and outdoor radios from lightning damage
  • Hotels, lodges and farms with long outdoor cable runs to cameras, radios or access points
  • Installers who want to reduce storm-related service calls on rooftop and mast installations

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.