Ubiquiti PowerBeam ac High-Performance airMAX Bridge (PBE-5AC-500): 27dBi Dish Radio for Long-Distance Point-to-Point Backhaul
The Ubiquiti PowerBeam ac (PBE-5AC-500) is an outdoor 5GHz airMAX AC bridge that pairs a 500mm dish reflector with an integrated radio for a 27dBi gain. It is built for long-distance point-to-point (PtP) links and high-performance CPE connections, where a narrow, focused beam reaches a distant tower or building and rejects noise from the sides. In addition, it supports up to 450+ Mbps real TCP/IP throughput with 2×2 MIMO, connects through one Gigabit Ethernet port and draws a maximum of 8W. Furthermore, a protective radome covers the dish to shield the radio from rain, dust and sun, while a built-in mechanical tilt bracket speeds up alignment. As a result, a pair of PowerBeams can carry internet, VoIP and CCTV traffic between sites many kilometres apart.
In practice, this is the radio WISPs and enterprises choose when a NanoStation or LiteBeam cannot reach far enough. For example, a WISP can run a backhaul link from a Nairobi data point to a relay tower on the Ngong Hills or in Machakos, then feed local sector access points from there. Similarly, a quarry in Athi River or a tea factory in Kericho can link a distant weighbridge or field office, where staff use HP Desktops, back to head office over one wireless hop. Meanwhile, Ubiquiti’s airMAX AC TDMA protocol and the airView spectrum analyser in airOS help keep the link stable on a busy 5GHz band. However, its wind survivability is rated at 96km/h, so mount it on a sturdy pole and avoid fully exposed peaks.
Key Features
In short, this PowerBeam bridge stands out in five areas:
- 27dBi gain from a 500mm dish reflector on 5GHz (5150–5875MHz)
- Up to 450+ Mbps real TCP/IP throughput with 2×2 MIMO airMAX AC
- Gigabit Ethernet port with 24V passive PoE adapter included
- Protective radome and UV-stabilised outdoor enclosure
- Built-in mechanical tilt for quick alignment on long links
Technical Specifications
Specifically, the table below details every core specification of the Ubiquiti PBE-5AC-500:
| Specification | Details |
|---|---|
| Brand | Ubiquiti (UISP airMAX) |
| Model | PBE-5AC-500 (PowerBeam ac) |
| Product Type | 5GHz airMAX AC dish bridge / CPE |
| Operating Frequency | 5150–5875MHz (worldwide) |
| Antenna Gain | 27dBi |
| Dish Reflector | 500mm |
| MIMO | 2×2, dual polarisation |
| Throughput | Up to 450+ Mbps real TCP/IP |
| Max. Output Power | 24dBm |
| Built-In Mechanical Tilt | +20° to -10° |
| Software | airOS 8 with airView spectrum analyser |
| Processor | Atheros MIPS 74Kc, 720MHz |
| Memory | 128MB DDR2, 16MB flash |
| Networking Interface | 1 x 10/100/1000 Ethernet port |
| LEDs | Power, LAN, WLAN |
| Power Supply | 24V, 0.5A Gigabit PoE adapter (included) |
| Power Method | Passive PoE (pairs 4, 5+; 7, 8 return) |
| Supported Voltage Range | 20–26V DC |
| Max. Power Consumption | 8W |
| Enclosure | Outdoor UV-stabilised plastic |
| Dimensions | 520 x 520 x 308mm (without radome); 525 x 525 x 315mm (with radome) |
| Weight | 2.35kg (without radome); 3.15kg (with radome) |
| Wind Survivability | 96km/h |
| Wind Loading | 264.6N at 96km/h |
| Mounting | Pole mounting kit (included) |
| Operating Temperature | -40 to 70°C |
| Operating Humidity | 5–95% non-condensing |
| Shock and Vibration | ETSI300-019-1.4 |
| Certifications | CE, FCC, IC |
| In the Box | Reflector, radome, antenna feed, rear housing, mounting and adjustment brackets, pole clamps and hardware, 24V 0.5A Gigabit PoE adapter with bracket, power cord |
Who This PowerBeam Is Best Suited For
As a result of this combination of specs, three types of users benefit most:
- Wireless internet service providers (WISPs) that need long-distance PtP backhaul between towers
- Quarries, farms and factories that link remote offices, gates or weighbridges to head office
- Network integrators who build high-throughput wireless links where fibre is too costly to lay


Reviews
There are no reviews yet.